Reconditioning a battery is a sensible way to refurbish old and dying batteries and make them good a new. So when you do so, not only does your cost in purchasing a new battery reduce, you also leave behind less carbon footprints.
The question that arises in the minds of most is ‘does reconditioning a battery really work’. You also wonder whether you need to be technically savvy do get this job done. Well, there are many more questions. Let me answer these through the means of my write-up.
>>> Click Here to Learn an Easy Method to Bring Old Batteries Back to Life & Save Thousands of $$$ <<<
Reconditioning a Battery Article Contents
1) What is Reconditioning a Battery?
2) Does Reconditioning a Battery Work?
3) How can I Recondition My Battery at Home?
4) What Equipment do I Need to Recondition My Battery at Home?
5) How do I Recondition My Car’s Dead Battery?
6) How Do I Recondition My Laptop’s Battery?
7) How do I Recondition a Lead Acid Battery?
8) How do I Recondition a Hybrid Car Battery?
9) How do I Recondition NiCad Battery?
10) How Long Does it Take to Recondition a Battery?
11) Does Putting an Aspirin in a Battery Improve its Life?
12) Can Dead Car Batteries be Reconditioned?
13) How can Epsom Salts Help my Battery?
14) Does Pouring Coke in a Car Battery Recondition it?
15) How can I Apply Vaseline on the Terminals of My Car Battery?
16) How Can I Clean My Battery Terminals with wd40?
17) How can I Uncorrode My Car Battery at Home?
18) What is the Blue Powder on my Car Battery?
19) How to Apply Grease on the Terminals of My Car Battery?
20) How can I Jumpstart My Car that has a Corroded Battery?
21) How to Start a Battery Reconditioning Business to Make Money?
22) How to Choose a Battery Reconditioning Kit?
23) When Not to Recondition a Dead Battery?
24) Conclusion
What is Reconditioning a Battery?
Reconditioning a battery is a method that helps bring back the full charge capacity of a malfunctioned battery. This in turn implies that your dying battery is brought back to life. It also implies that the battery is now capable of maintaining optimal electrolyte levels.
Lead Sulphate Crystals:
The two main concerns that often bog down your battery are ‘acid stratification’ and a ‘low charge’. You need to understand that a fully discharged battery tends to release acid. This acid tends to accumulate around the plates of your car’s battery.
These are also termed as lead acid sulphates. When their deposits exceed the permissible limit, lead acid sulphates tend to affect both the charge as well as discharge capabilities of your vehicle’s battery.
What Types Batteries can Be Reconditioned?
Well, in my opinion and as per my experience, almost all of these can be reconditioned. Nonetheless, there can be a few batteries that cannot be brought back to life. Well these, we shall not be discussing as of now.
The battery of your car can be reconditioned (the 12 volt variants), NiMH and NiCAD batteries too can be reconditioned. Pirus and golf cart batteries too can be reconditioned. I have successfully reconditioned gel batteries, AA and lithium-acid batteries as well.
Does Reconditioning a Battery Work?
Yes, reconditioning a battery really works. The condition here is that you need to have basic technical knowledge to execute this job perfectly. There are so many solutions to reconditioning your car battery online that you tend to get confused.
A vast majority of our population is of the opinion that an old battery needs to be thrown in the garbage can. This is not at all true. You can recondition an old and dead battery and make it as good as a new one.
Over here, the need to know the correct trick or hack is vital. When you know that secretive technique then, even a novice with absolutely zero technical knowledge can recondition his/her vehicle’s battery easily.
How can I Safely Recondition My Battery at Home?
While reconditioning a battery is advisable, you need to be very careful while doing so. The electrolyte content within any battery tends to contain harmful acids.
Here are a few precautions that you need to take so as to save your clothes, eyes, skin and even your floor/furnishings:
@ I always wear a pair of goggles. These have a special rubber cover that encapsulates my eyes from all sides. It helps avoid the battery acid from accidentally spilling into my eye.
@ I (LeanAndFit review staff)also wear a pair of rubber gloves. These allow me to save my hands and fingers from damage.
@ Acid present in electrolytes tends to stain my clothes whenever I try and recondition my dead battery. So, to save my clothes, I wear a pair of old overalls.
@ Once I open the battery, the acid fumes tend to spread all around. So, I like to recondition my batteries in an open area. If I have to do this within a room then, I ensure to keep the doors and windows open.
@ I also use a face mask that helps filter the acid fumes from entering my nasal cavity.
What Equipment do I Need to Recondition My Battery at Home?
Even before you initiate the process of bringing your car’s dead battery back to life, you need to first keep a few things handy. Here is a list of the essentials:
@ Distilled Water & Baking Soda: I use this combination to help clean the battery terminals. Any corrosion that is visible in the battery is cleaned by mixing these two ingredients.
@ Voltmeter: This is a meter that is required to measure the accurate reading of your battery’s charge. Any reading (of a battery) that is below 12.4 volts requires a reconditioning.
@ Bucket: This is to pour the electrolyte solution that you derive from the battery into the bucket. You also need the bucket to neutralize this solution using baking soda for the purpose.
@ Funnel & Screwdriver: A funnel is needed to pour liquid from the battery into the bucket. It is also needed to pour any liquid from the battery into the battery. A screwdriver is used for dismantling the battery.
@ Apron, Gloves and Goggles: An apron helps save your clothes from stains. The gloves protect your hands from stains. The googles shall stop any acid to reach your eyes.
@ Epson Salt: This is used to replenish the solution that is present in your battery. The electrolyte solution gets a fresh lease of life via Epson salt.
@ Battery Reconditioning Charger: This is a special devise that helps regulate the amount of voltage that your reconditioned battery is getting. It also controls the current level. Doing so enhances the lifespan of your reconditioned battery.
How do I Recondition My Car’s Dead Battery?
When your car battery does down, you simply cannot run the car. You need to either get a replacement (which is expensive) or recycle the dead battery. If you choose the latter then, your dead car battery can be reconditioned to work upto 71% as good as a new battery.
Here are 4 simple steps to do this:
Step # 1: First of all, you need to get rid of the caps and the rubber casing that protects the battery. You need to place them neatly in an empty tool box.
Step # 2: Now, you can fill some water into the battery and recharge it for 60 minutes. It is recommended that you use distilled water and fill it till the permissible limit.
Step # 3: The water after about 60 minutes shall start to emit ripples. In the absence of ripples, simply connect the positive wire to the negative and the negative to the positive. The rippling effect is now bound to happen. Reconnect the wires in the correct position.
Step # 4: The acid inside the battery can also be replaced with new acid. Simply mix it with distilled water. Thereafter, charge the battery for a few hours.
You now have an almost new battery that shall function 65% to 75% as efficient as a new battery. I believe this percentage is good enough for running any vehicle.
How Do I Recondition My Laptop’s Battery?
Losing a laptop battery is heart-breaking indeed. Not only does that imply that you get hold a new one, it also empties your wallet. Most people prefer to buy a new laptop rather than spend money buying a new battery.
Nonetheless, you can recondition the dead battery of your laptop. Only old and malfunctioned batteries should be dealt with here. The methods I shall share with you are free of any cost.
You need to simply give time and make some effort. These methods can work with both removable as well as non-removable laptop batteries.
Method # 1:
You can do this with a laptop whose battery can be removed. Well, simply place the laptop for charging. When fully charged, remove the battery and test if your laptop works. If it does, the life of the battery is improved. If not, try the other methods, I’m listing below.
Method # 2:
The second method too works with a removable laptop battery. Remove the battery and wrap it in plastic. Store it in the deep freeze for about 13 hours.
Take it out of the plastic wrapping and dry it with a clean cotton cloth. Replace the battery to its rightful place – the laptop. Recharge it fully and watch out for any acid leaks. If there are none, your battery is good to last you a very long time.
Method # 3:
In this method, you need to recharge the battery over and over again. So, here is how you do it. Plug your battery to the charger and wait till it is fully charged.
Allow the battery to drain till it has about 6% charge left. Recharge it again to its full capacity. Repeat this process a few times. Your battery would soon be as good as new.
Method # 4:
In this method, you need to charge the laptop’s battery to 100%. Thereafter, simply unplug the charger and allow the laptop to remain idle till the battery drains completely.
After leaving the laptop for around 6 hours in this state, recharge it again. This time around, recharge the battery to its 100% capacity. This method helps add a new lease of life to your battery.
Method # 5:
In my opinion, variations in temperature help improve your battery life. This can be done by turning on the air conditioning unit when it gets warm.
Alternately, connect a cooling pad underneath your laptop. This stops the laptop battery from overheating. A cooling pad also prolongs the life of your battery.
How do I Recondition a Lead Acid Battery?
If you want a few more years added to your lead acid battery then, you need to recondition it. This is a careful procedure due to the presence of acid in the battery. Well, here are the steps:
>>> Remove the rubber encapsulation from the battery. There are several caps on the battery. Open each and every one of them.
>>> Measure the battery charge using a voltmeter. The voltage should be in between 13 to 14 volts.
>>> Fill distilled water into the battery. Recharge the battery. This should fix any faults within the battery.
>>> Replace the existing acid from the battery after emptying the old one. Doing so shall make your battery good as new.
>>> Always try and put the battery in a slow charging mode. This shall take 10 to 14 hours before the battery is fully charged.
>>> In my opinion, even if the battery cells are malfunctioning, the above procedure shall allow you to avail 75% of the original charge.
How do I Recondition a Hybrid Car Battery?
A hybrid battery is usually used in hybrid vehicles. Nowadays, most cars make use of a hybrid battery. Owing to this very purpose their upkeep is of vital importance.
Long Lasting: It is good to know that hybrid batteries have a shelf life of 3,22,000 kilometers. If it is damaged and has surpassed its warranty period then, you need to buy a new one. A new hybrid battery shall set you back by $3200 (on an average).
Fix Module Faults: So, in order to avoid this expense, you need to fix the damaged battery. This can be done by merely changing the modules.
Each hybrid car battery contains modules. Simply replace these with a new one. The cost of this replacement is roughly $710. Once the damaged modules have been replaced by new ones, your hybrid battery shall last 5 to 6 years.
How do I Recondition NiCad Battery?
Batteries that use metallic cadmium and nickel oxide hydroxide as their electrolytes then, they are termed NiCad batteries. They are rechargeable and are used in camcorders, computers and electrical devises that require an even supply of energy to function optimally.
The main reason why NiCad batteries die out sooner than expected is owing to sulfur deposits. These crystals tend to get stuck to the battery terminals. When that happens, your NiCad battery is unable to avail a full charge. Nonetheless, following the below mentioned steps can help you last these batteries longer.
@ Get hold of an old camera that has flash mechanism. Make sure that you know how to dismantle the camera. If not, use a friend’s help.
@ You would find a capacitor within the flash camera. This is what you need to get the job done.
@ Affix wires to a battery holder and connect it with a switch. Insulate these wires to ensure that no power passes through them.
@ Onto the holder, you place your malfunctioned NiCad battery. Onto the capacitor, you place another battery- this time an alkaline one.
@ Press the switch to ‘power’ mode. An LED light shall start to glow. This is accompanied by a faint rustle.
@ This is a clear indicator that the sulfur deposits on your battery terminals are being scrubbed clean.
@ Repeat this steps two to three times for a short duration. Soon your NiCad battery shall begin to function like new.
How Long Does it Take to Recondition a Battery?
The time taken to recondition an old battery is completely dependent on the current status of the machinery. At the same time, you need to follow all the mentioned steps (as I have mentioned under the battery reconditioning process for cars).
If you need time to get together the necessary items for battery reconditioning then, the process shall take more time. If you have everything handy and you are able to follow all the steps correctly, the time taken shall be less.
Overall, you should be able to recondition a battery within a 48 hour time frame. I am assuming this time includes getting all the necessary equipment together.
Does Putting an Aspirin in a Battery Improve its Life?
Well, aspirin can start a battery but it shall not improve the battery life. I will try and explain this phenomenon in simple words. Now, car batteries use lead-acid, which is 38% sulfuric acid and the remainder, is water.
When lead dioxide plates and lead are lowered into this electrolyte solution, it creates a reaction. The electrons thus produced ferry through the conductors thereby generating electricity. This is how your car starts.
The Good Side of Aspirin
Now aspirin acts as an addictive. When crushed aspirin pills are added to the electrolyte solution, it creates a burst of energy. When the current is passed into the dead battery again, it balances the electrolytes. So, your car battery works and you drive away with a smile.
How does it Work?
@ An average car battery contains 6 cells of 2 volts each.
@ Pull off their caps and the rubber casing to reveal the cells. Use a screwdriver for the same.
@ Crush three tablets of aspirin and place them in each cell opening. So, if your battery contains 6 cells then, you use 15 to 18 crushed aspirin tablets.
@ The sulphuric acid present in the battery merges with acetylsalicylic acid present in the aspirin tablets. This creates a reaction that jump-starts your battery.
@ As this chemical reaction releases acetic acid, it helps power-up your battery. Nonetheless, it shortens the overall life-span of your battery.
Can Dead Car Batteries be Reconditioned?
Yes, dead batteries can be fully reconditioned. If you know the procedure and have time at hand, you can easily hope to recondition your old and dying battery.
Nonetheless, be rest assured that the functional capability of a reconditioned battery shall be equivalent to 70% of a brand new battery. So, while you can use a battery that you were about to throw in a garbage can, it is not as good as new (it can never be).
How Long can My Reconditioned Battery Last?
This is a question that most people aspiring to recharge their batteries ask. The total number of months or years that your reconditioned battery shall last depends on how well the reconditioning process was performed.
If you did everything right then, your battery shall last longer. In case the sulfication on your battery was not so bad then again, the reconditioning shall prolong its shelf-life considerably.
Also, you need to follow all the steps mentioned in the battery reconditioning process. When you do so, you shall have a long lasting battery and vice-versa.
In my opinion, a reconditioned battery should provide 70% power derived by a new battery. This implies that it can last you another 3 to 4 years.
How can Epsom Salts Help my Battery?
If you have a lead-acid battery then, Epsom salt solution shall help prolong its shelf life. Not only is this method cost-effective but also effective. This is how you can easily hope to relive the battery and make it good as new.
How to Recondition Your Lead-Acid Battery with Epsom Salt?
The First Step: In the very first step, you need to protect yourself. Wear an overall, a pair of gloves and protective eyewear. Then remove the battery from your car and place it in a secure place.
The Second Step: Mix 113 millilitres of Epsom salt in 946 millilitres of distilled water. Make sure that the water is warmed to 150 degree Fahrenheit.
The Third Step: Make a paste (slightly sticky) made from distilled water and baking soda. Make sure you keep the quantity of baking soda double to that of distilled water while making the paste.
The Fourth Step: Place a hard brush into the solution and scrape the battery terminals with it. This should remove the corrosion.
The Fifth Step: You need to now remove the old electrolyte solution present within the battery. Pour it into a bucket after unhooking the battery caps.
The Sixth Step: Mix a pound of baking soda into the old electrolyte solution. This shall neutralize the solution and make it user worthy.
The Seventh Step: Pour this solution into the battery cells. Shake the battery for a few seconds and remove the solution into the bucket. Repeat this process twice over. This helps dissolve the lead sulfates that are clogging the battery plates.
The Eighth Step: Pour the Epsom salt solution that you had prepared in Step Two. Pour this liquid into each cell. Use a funnel for precise pouring.
The Ninth Step: Close the caps and place the battery to a slow charge. Let is charge for 24 hours at 12V/2amp. Thereafter, measure the current voltage. It should display a reading of about 12.4 volts.
The Tenth Step: If the charge is less than 12.4 volts then, repeat the process all over again. A battery load tester can make this task easier. You need to buy one though.
Does Pouring Coke in a Car Battery Recondition it?
Yes, you can try and clean the battery terminals using coke. Switch off the vehicle (power off the ignition) before trying out this process. The purpose here is to remove the sulfur deposits that are clogging the battery terminals.
The Material Required:
When the corrosion is removed, your car’s ignition related issues shall be resolved. You would need a hard bristle tooth brush and a cotton cloth as well. Some water may also be needed.
The Process:
Step # 1: Remove the cables from the battery. The trick here is to avoid getting shocked in the act. So, remove the negative cable first using a wrench. Then, remove the positive one.
Step # 2: Simply pour coca cola from a cup onto the areas that seem rusted. A rippling effect shall precede this act. To remove rust from the bolts and other areas of the battery, simply brush these with a toothbrush.
Step # 3: Take a glass of water and pour over the cleansed surface. This shall reduce the coke stickiness. Wipe the coke stains/deposits clean with a cotton cloth.
Step # 4: Thereafter, simply clamp the positive cable to the battery. Thereafter, affix the negative cable with the battery.
Hey, if you see a spark emerge from the terminal, do not be scared. It is a sign that your battery is fixed properly and is in better condition than before.
How can I Apply Vaseline on the Terminals of My Car Battery?
You can apply Vaseline to the terminals of the car battery. Simply wear a pair of protective gloves before indulging in this act. Thereafter, you need to make sure that you apply petroleum jelly liberally all across the terminals.
When you apply petroleum jelly, you tend to strengthen the connections within the battery. This acts as an agent to transfer electricity from the battery to your vehicle.
At the same time, Vaseline tends to keep the battery terminals free from corrosion. So, this in turn helps prolong the life of your battery. Application of petroleum jelly needs to be a part and parcel of your battery upkeep and cleansing process.
>>> Click Here to Learn an Easy Method to Bring Old Batteries Back to Life & Save Thousands of $$$ <<<
How Can I Clean My Battery Terminals with WD40?
WD-40 is a ‘lubricant’ that has been helping mechanics in keeping their wipers and batteries clean since the year 1950. Almost 61% households in USA make use of this cleaning solution.
WD stands for ‘water displacement’ and it helps keeps moisture away. It is a mixture of Aliphatic Hydrocarbon, paffrin, carbon Dioxide and aliphatic hydrocarbons. Alkens derived from carbon as well as mineral oils, is also present in WD-40 solution.
You can spray WD-40 onto your battery terminals to remove traces of rust and corrosion. Nonetheless, you need to be careful while doing so. Spray a limited quantity only.
If your battery is weak or has lose terminals then, spraying ED40 can help improve your battery performance. Nuts and bolts can also be freed of rust using this spray.
How can I Uncorrode My Car Battery at Home?
If your car batteries are corroded then, you need to remove their rust. This helps prolong the life of your battery. The transient air flow is what is restricted when your battery terminals are blocked by rust and muck.
Here is how you can remove the corrosion from your car battery:
>>> Unplug the cables connecting your battery. As I have mentioned above, always disconnect the negative cable first. This is to be followed by the positive cable.
>>> If the battery insulation displays signs of cracking, peeling or corrosion then, you need to even-up the frayed surface.
>>> You can then apply battery cleaners by getting one from a workshop. These need to be of commercial grade only.
>>> If you do not have access to a battery cleaning liquid or spray, use baking soda or even coke for the same purpose.
>>> Scrub the corroded surface clean using an iron bristle brush. Wipe any liquid clean using an absorbent and dry cloth.
>>> Affix anti-corrosion pads to your battery terminals. This helps your battery from rusting in the near future.
What is the Blue Powder on my Car Battery?
The blue powder that is usually visible on your battery is a clear sign of corrosion. The posts and terminals exhibit the bluish, sometimes whitish or even greenish color.
In case your battery has copper connectors then, hydrated copper sulphate deposits tend to exhibit a bluish color. When you see bluish deposits on your battery then, the circuit is compromised.
This reduces the relay of energy or electric flow within the battery. When the electric flow within the battery is compromised, it stops your car from starting.
How to Clean the Blue Powder from Your Car Battery?
>>> Remove the cables attached to the battery. The negative precedes the positive cable in the removal process.
>>> Check the insulation of the battery. If it is dried or cracked then, it needs to be rectified.
>>> If the cables are brittle or frayed then, change them. This shall improve the flow of current within the battery.
>>> Apply battery cleaner of a commercial grade onto the terminals. This should clean the corrosion.
>>> If you do not have a battery cleaner then, make use of baking soda or coke.
>>> The posts as well as the terminals of the battery need to be cleaned via a dry cotton cloth.
>>> I suggest that you place anti-corrosion pads to protect the terminals.
>>> Reconnect the battery cables. First connect the positive and then, the negative cable.
>>> Coat the battery terminal and post with anti-corrosion spray.
How to Apply Grease on the Terminals of My Car Battery?
The main reason why your battery dies down before its due time is owing to corrosion. When rust builds up onto the battery terminals and bolts, the natural flow of current within the battery is interfered with. Hence, your car battery does not charge to its optimal capacity.
In order to minimize this fault and kick-start your dead battery, you need to maintain optimal current flow within the battery. The application of grease (white lithium) helps restore optimal current flow.
Simply apply this grease onto the terminals. This needs to be done when the cables have been tightened. Grease creates a barrier between the moisture and the battery surface, thereby reducing corrosion.
The application is simple. Wear a pair of gloves. Dab a generous layer of white lithium grease across your finger and paste it around the battery terminal.
How can I Jumpstart My Car that has a Corroded Battery?
Your car is as dear to you as your home. Most people travel to work and for leisure using their car. It also helps you scrape through emergency crisis. So, if your car stops working, it can get quite frustrating. More than often, your car not starting is a case of a faulty battery.
Here is how you can jumpstart your dead battery and be off to your destination within 20 minutes:
Jump Box is the easiest way to get the job done.
@ This is also termed as a Jumper Box as it is a portable battery charger.
@ It has a black alligator clip and a red alligator clip. Connect the red to the positive terminal of the battery and the black with the negative.
@ After making sure that your Jumper is fully charged, you now start charging your vehicle’s battery.
@ Once the car’s battery is capable of starting your car, remove the alligator clips. You are good to go.
Can You Jumpstart a Corroded Battery?
The answer is ‘no’. In order for your Jumper Box to restart your car, your vehicle’s battery needs to be clean and free from corrosion. You need to first clean the battery and remove the corrosion before jumpstarting it.
In case you do not have baking soda at hand then, use coke to clean your battery with. Pour some coke onto the corroded area and wipe it clean with a dry cloth. Thereafter, you can initiate the JumpStart process.
How to Start a Battery Reconditioning Business to Make Money?
In today’s world, emphasis is laid on green solutions to meet your power based needs. For the sake of a cleaner environment, people have stopped throwing used batteries in the garbage can and instead, started reconditioning them.
Now, not everyone has the time or the material needed to recondition used batteries. With rising demand for battery reconditioning services, you have the opportunity to make some money.
Well, here are some tips:
Prepare Your Base:
Even before you begin to recycle other’s batteries, you need to learn the art of doing this right. The charge capacity, solving reverse cell issue and rejuvenating dead batteries are a part and parcel of your job. You need to know these on your fingertips.
You also need to be well versed with different types of batteries. These may include but not limited to Ni-MH, Lithium-Ion, Ni-Cd and Lead Acid. If possible, undergo a government approved industrial training course on battery reconditioning.
Prepare Your Blue Print:
Even before you initiate any business, you need to have a plan of action ready. You need to conduct a market research and based on the report, plan your business strategy.
You need to identify the initial investment, the recurring expense, the customer base and how you shall recover the money you invested. Then, you need to prepare an action plan to make profits.
Establish an Office:
Purchase the necessary equipment that is needed to kick-start your battery reconditioning business. For this very purpose, you need to gather the necessary material.
Some of the basic equipment includes hydrometer, load tester, battery analyzer, acid boxes, screwdriver sets, buckets, gloves, goggles, drills etc.
The Registration and Permit:
In the very next step, you need to register your business. Make sure that you get the desired permits from your local authorities. Doing so shall permit you to initiate battery reconditioning business legally. If you have an issue with this process then, seek the help of a professional to get the job done.
Establish an Office & Spread the Word Around:
In the last and final stage, you need to create a workplace. This includes your office space as well as a workshop. Get the desired license for this purpose.
Thereafter, you need to market your business. You could use both print as well as television media. Door to door advertising is also a good idea. Touch base with automobile workshops, car accessory stores to make new clients.
Make sure you have an online presence of your battery reconditioning business. Use online marketing methods to attract more and more customers.
How to Choose a Battery Reconditioning Kit?
Battery reconditioning equipment is needed to ensure that your battery remains in top shape. The use of this kit is to enable you to recondition your dead battery without moving an inch away from your easy chair.
Here is a list of what all you need in order to conduct DIY battery reconditioning at home:
Equipment Needed for Reconditioning Car Batteries:
Voltmeter: This is a devise that senses a gap between the electrical transfers between two terminals. Even difference in microvolts can be measured successfully via this devise. This instrument works both with DC and AC.
Battery Reconditioning Charger: This electronic devise permits you to bring a dead battery to life. Over here, you do not need to put in any extra effort.
Made via inverter technique, battery reconditioning chargers remove sulfate crystals, provide accurate readings and give the right amount of power to your battery.
Baking Soda: This product helps create a reaction that removes tough corrosion stains from the surface of your battery. It helps reduce acids into neutral state thereby allowing the battery to remain clean.
Epsom Salt: Made from oxygen, magnesium and sulfur, Epsom salt is a natural abrasive. It scrapes away corrosion, dirt and grime from the battery.
Disposable Gloves: These are needed to protect your hands from battery acid, corroded surface and wires.
Distilled Water: It is deionized water. It is free from contaminants and minerals.
Funnel: This simple devise is used for pouring liquid inside battery cells. It avoids the liquid from spilling over.
Goggles: To save your eyes from acid, you should wear a pair of goggles. If possible, pick one that has rubber coating on all sides. This further protects your eyes from damage.
Screwdriver: In order to open the cables connected to the battery, you need a screwdriver. One that has a flat head shall be preferred over the round headed screw drivers.
Bucket & Overalls: A bucket is vital for ensuring that you pour liquid solution (electrolyte) to and from the battery. Wearing overalls shall protect your clothes from getting stained.
Jumpstart Kit: This is a machine that helps your car battery start with the aid of a power devise. The jumpstart devise provides power to your dead car battery using its own battery backup.
Hydrometer: A hydrometer helps analyze the electrolyte gravity in your battery. This is helpful when you are reconditioning your car battery.
Equipment Needed for Reconditioning Laptop Batteries:
Cyanoacrylate Adhesive: This product is needed when you are restoring the dead battery of your laptop. It helps glue your battery parts to the laptop without damaging it in the act.
21 Watt Auto Bulbs: This is needed when you are trying to repair your laptop battery. These bulbs help check the level of current flowing through the laptop batteries.
Grinding Sponge or Thin Sandpaper: A sandpaper of thin variety and a metal brush are needed to clean the battery terminals. You can also use a grinding sponge for the same purpose.
Thick Blade Cutter: Also known as a paper cutter, this instrument helps slice through battery housing. In case you do not have one handy, use your kitchen knife instead.
Cu: Basically, you need copper wires to repair the damaged laptop battery. It helps connect auto bulbs to the laptop in order to check the voltage.
Equipment Needed for Reconditioning Cellphone Batteries:
Universal Charger: If you have to repair dead cell phone batteries then, you need a universal charger. This devise can be attached to the cell’s battery for reconditioning it.
300Ohm and Less Resistor level: This devise is also used for reconditioning cell phone batteries. It adjusts the flow of current into the battery to adjust the voltage.
Equipment Needed for Reconditioning AA Batteries:
Awl: This is a sharp edged devise that is used to make holes in AA batteries. So, in order to fill these batteries with liquid, you need to make holes. This is what is achieved via the Awl.
Thin Syringe: Once again, this is needed to cleanse an AA battery. A thin syringe shall do the trick here.
Industrial Clay: Once again, this is used to recondition AA batteries with. It helps seal these batteries. You can also use resin for the same purpose.
When Not to Recondition a Dead Battery?
Lack of Correct Equipment:
If you do not have the necessary safety equipment to back your reconditioning process then, avoid indulging in it. There is acid in the battery that can spill and even explode.
To avoid getting burnt in the act, you need to first get an apron, gloves, goggles and other safety devises. If you do not have these handy then, avoid reconditioning your battery.
Battery is Swollen or Cracked:
After you have gathered all the necessary safety equipment to recondition your old battery, you are all set to initiate the process. Nonetheless, even before you do so, make sure you check the battery condition.
If the battery is cracked or appears to be swollen then, it is a high risk job, it may explode or the acid might spill. Moreover, cracked batteries usually never get reconditioned.
The Current Reconditioning Status:
If you have reconditioned your battery previously then, you may not be able to do so again. Ideally, two times is considered the maximum attempts for reconditioning a battery.
If you try recondition your battery the third time, it may not work. In case it works the third time, definitely do not attempt it the fourth time. Your battery has reached its maximum recharge capacity.
The Timespan after Reconditioning:
After completing your battery reconditioning process, do remember that the corrected battery would not last more than a year. In some cases, it can last two years as well. If your battery has passed this time span then, it is time to get rid of it.
Conclusion
Battery reconditioning is a wise option indeed. Not only does it save you the hassle of purchasing a new one, it also helps you run your car flawlessly. You also learn a new art.
Battery reconditioning process is rather simple to learn and simpler to execute. You just need to learn the process of fixing your dead battery the correct way.
Besides prolonging the life of your current battery, battery reconditioning process helps you earn money as well. You can start a battery reconditioning business to make profits.
Simply put in some extra effort to learn the process in detail. Soon, you shall begin to make some serious money.